高一致性电池模组结构件模具快速成型与尺寸稳定性分析OA
Rapid prototyping and dimensional stability analysis of high-consistency strutural components for battery module molds
针对新能源汽车动力电池模组结构件量产过程中存在的一致性差、热变形大,以及开发周期长等问题,本文提出一种集数字化建模与智能优化于一体的快速成型方案.首先,基于材料流变特性分析,利用正交实验设计筛选出熔体温度、模温、注射速度及保压时间等关键工艺敏感因子.其次,引入改进遗传算法,对注射参数及内部随形冷却系统布局实现多目标同步寻优.为精准控制非线性翘曲,构建了包含广义热粘塑性本构方程的热力耦合残余应力演化模型,并结合神经网络建立残差预测校正机制,通过加权融合公式提出型腔尺寸主动补偿策略.实验验证采用模具嵌入式八通道热敏电阻阵列监测温度场分布,配合高精度三坐标测量仪采集零件实物尺寸数据.连续 30 d 的生产跟踪实验结果表明,应用补偿策略后,关键尺寸的过程能力指数由初始 0.79 跃升至 1.42,均方根误差降至 0.054 mm,尺寸综合合格率突破 96.7%.与传统经验模式相比,试模周期缩短约 30%.该方案经实测数据验证,有效抑制了成型缺陷,实现了模具全生命周期内尺寸稳定性的可靠控制.
Aiming at the problems of poor consistency,large thermal deformation and long development cycle in the mass production process of power battery module components of new energy vehicles,this paper proposes a rapid prototyping scheme integrating digital modeling and intelligent optimization.Firstly,based on the analysis of rheological properties of materials,the key process sensitive factors such as melt temperature,mold temperature,injection speed and holding time were screened out by orthogonal experimental design.Secondly,the improved genetic algorithm is introduced to realize multi-objective synchronous optimization of injection parameters and internal conformal cooling system layout.To accurately control nonlinear warping,a thermo mechanical coupled residual stress evolution model containing a generalized thermo viscoplastic constitutive equation was constructed,and a residual prediction correction mechanism was established by combining neural networks.An active compensation strategy for cavity size was proposed through a weighted fusion formula.The experimental verification uses an embedded eight channel thermistor array in the mold to monitor the temperature field distribution,combined with a high-precision coordinate measuring instrument to collect physical dimension data of the parts.The results of continuous 30 d production tracking experiments show that after applying the compensation strategy,the process capability index of key dimensions jumped from the initial 0.79 to 1.42,the root mean square error decreased to 0.054 mm,and the comprehensive qualification rate of dimensions exceeded 96.7%.Compared with the traditional empirical mode,the trial period is shortened by about 30%.The scheme is verified by the measured data,which effectively suppresses the forming defects,realizes the reliable control of the dimensional stability of the die in the whole life cycle.
冯帆;朱可宁
陕西国防工业职业技术学院,陕西 西安 710300陕西国防工业职业技术学院,陕西 西安 710300
矿业与冶金
电池模组结构件模具快速成型尺寸稳定性改进遗传算法主动补偿
battery modulestructural componentrapid prototypingdimensional stability
《模具技术》 2026 (4)
29-35,7
2026年度陕西国防工业职业技术学院科研计划项目"高一致性电池模组结构件快速成型与尺寸稳定性分析研究"(编号:Gfy26-09)2023年度陕西高等职业教育教学改革研究委托项目"中高职贯通一体化人才培养模式创新与实践"(编号:23GW006).
评论