首页|期刊导航|金属加工(热加工)|放电能量对6061Al/T2Cu异种材料电磁脉冲焊接界面形貌及力学性能的影响

放电能量对6061Al/T2Cu异种材料电磁脉冲焊接界面形貌及力学性能的影响OA

The effect of discharge energy on the interface morphology and mechanical properties of 6061Al/T2Cu dissimilar materials in electromagnetic pulse welding

中文摘要英文摘要

采用电磁脉冲焊接实现了6061Al和T2Cu异种材料的连接,结合数值模拟和试验探究了放电能量对界面形貌的影响、波形界面的形成过程和界面元素扩散问题.研究表明:放电能量的提高增大了6061Al受到的电磁力,提高了碰撞速度,而碰撞角度不受影响.界面形貌由平直界面向不规则的波形界面和剪切波界面转变,最后转变形成过渡层,波幅从1.55μm增至4.61μm.在持续的冲击作用下,接触点前方不断产生新的凸起,既有凸起则逐渐增大并相互嵌入,最终形成波形界面结构.界面有无过渡区且均发生元素扩散,接头的最大拉剪载荷为10730N.随着放电能量的提高,母材间发生冶金结合,从而提升了接头的力学性能.

This study employed electromagnetic pulse welding(EMPW)to join 6061Al and T2Cu as dissimilar materials.The effects of discharge energy on interface morphology,wave formation mechanisms,and element diffusion were systematically investigated through numerical simulations and experiments.It was shown that the increase in discharge energy increased the electromagnetic force on 6061 Al and increased the collision velocity,while the collision angle was not affected.The interface morphology changes from a flat interface to an irregular wave interface and a shear wave interface,and finally transition forms a transition layer,with the wave length increasing from 1.55μm to 4.61μm.Under continuous impact,new protrusions continuously form ahead of the contact point,while existing protrusions gradually enlarge and interlock with each other,ultimately forming a waveform interface structure.Element diffusion occurs at the interface with or without the transition zone,with a maximum tensile shear load of 10730N at the joint.As discharge energy increases,metallurgical bonding occurs between the base metals,thereby enhancing the mechanical properties of the joint.

刘文龙;沈文龙;周春培;王善林;张体明;陈玉华;谢吉林

南昌航空大学江西省高端装备极端制造技术重点实验室 江西南昌 330063南昌航空大学江西省高端装备极端制造技术重点实验室 江西南昌 330063南昌航空大学江西省高端装备极端制造技术重点实验室 江西南昌 330063南昌航空大学江西省高端装备极端制造技术重点实验室 江西南昌 330063南昌航空大学江西省高端装备极端制造技术重点实验室 江西南昌 330063南昌航空大学江西省高端装备极端制造技术重点实验室 江西南昌 330063南昌航空大学江西省高端装备极端制造技术重点实验室 江西南昌 330063

Al/Cu异种金属电磁脉冲焊接数值模拟界面形貌

Al/Cu dissimilar metalselectromagnetic pulse weldingnumerical simulationinterface morphology

《金属加工(热加工)》 2026 (10)

46-56,11

国家自然科学基金(52571043、U24A20117)江西自然科学基金(20242BAB23042).

评论