首页|期刊导航|长春工程学院学报(自然科学版)|基于三维有限元模拟的超前灌浆参数设计及加固防渗效应分析

基于三维有限元模拟的超前灌浆参数设计及加固防渗效应分析OA

Design of advance grouting parameters based on three-dimensional finite element simulation and analysis of reinforcement and seepage prevention effects

中文摘要英文摘要

针对TBM施工隧洞日涌水量达1 400 m3/h的强涌水工程难题,以快速止水、加固围岩等为核心目标,结合三维有限元数值模拟与现场实证验证,开展超前灌浆参数优化设计及加固防渗效应分析.根据隧洞地质条件、力学特征,采用弹塑性损伤理论与渗流场耦合理论构建三维有限元模型,数值模拟不同灌浆深度、灌浆压力、浆液配合比工况下的围岩变形、破坏特性及渗流分布规律;在此基础上,开展现场分序分段灌浆试验,校核并优化参数设置的合理性.结果表明,最优灌浆深度为20~50 m,采用0.5~10 MPa分级施加灌浆压力,按2∶1、1∶1、0.7∶1和0.5∶1逐级变换浆液水灰比时,围岩变形量最大降幅可达46.5%,破坏区深度减少41.9%,隧洞日涌水量由1 400 m3/h降至15.12 m3/h,堵水效率达98.9%.采用本文提出的分级分序灌浆参数及施工方法可实现高涌水TBM隧洞的高效加固防渗,可为同类工程设计与施工提供参考.

In response to the difficult problem of strong water inflow in TBM construction tunnels with a daily water inflow of 1 400 m3/h,with the core goals of rapid water stop and reinforcement of surrounding rock,combined with three-dimensional finite element numerical simulation and on-site empirical verifica-tion,advanced grouting parameter optimization design and reinforcement anti-seepage effect analysis were carried out.Based on the geological conditions and mechanical characteristics of the tunnel,a three-dimen-sional finite element model is constructed using the coupling theory of elastic-plastic damage and seepage field.Numerical simulations are carried out to investigate the deformation,failure characteristics,and seep-age distribution of surrounding rock under different grouting depths,grouting pressures,and slurry mix ra-tios;On this basis,on-site sequential and segmented grouting tests will be conducted to verify and optimize the rationality of parameter settings.The results show that the optimal grouting depth is 20-50 m,and the grouting pressure is applied in stages of 0.5-10 MPa.When the water cement ratio of the slurry was gradu-ally changed at 2∶1,1∶1,0.7∶1,and 0.5∶1,the maximum reduction in rock deformation could reach 46.5%,the depth of the failure zone decreased by 41.9%,the daily water inflow of the tunnel decreased from 1 400 m3/h to 15.12 m3/h,and the water blocking efficiency reached 98.9%.The use of the graded and sequential grouting parameters and construction methods proposed in this article can achieve efficient reinforcement and anti-seepage of high water inflow TBM tunnels,providing reference for the design and construction of similar projects.

尹华阔

中铁十八局集团隧道工程有限公司,重庆 401120

交通工程

三维有限元模拟超前灌浆加固防渗岩体变形渗流分布

three-dimensional finite element simulationadvance groutingreinforcement and seepage pre-ventionrock mass deformationseepage distribution pattern

《长春工程学院学报(自然科学版)》 2026 (3)

33-38,6

10.3969/j.issn.1009-8984.2026.03.005

评论