复合推进剂混合过程中安全性的数值模拟分析OA
Numerical Simulation Analysis of Safety during the Mixing Process of Composite Propellants
为揭示立式混合机内复合推进剂药浆混合过程中的安全机制及混合效果,采用计算流体动力学(CFD)方法,建立了均质单相流体稳态模型.针对12 组不同药浆黏度(331.342~1 260.216 Pa·s)与桨叶转速(42.50~85.00 r/min)的工况,系统模拟并分析了压力、温度、剪切应力、扭矩及混合流场等关键参数的变化规律.结果表明:黏度、转速与压力、剪应力及扭矩均显著正相关;在1 260.216 Pa·s、85.00 r/min 高参数组合下,最大剪应力达6.867 MPa,远超3.180 MPa 安全阈值;而温度升高有限(最高61.66℃).表明该工况下热累积风险有限,机械剪切作用更值得关注.识别出7 种高风险工况,主要集中于较高黏度和较高转速条件.通过量化流动死区占比、流场覆盖率及轴向循环效率评估混合效果发现,提高转速可显著改善混合的均匀性与效率,但会同步增加安全风险.进一步通过平衡指数耦合安全与混合性能,明确了兼顾安全与效率的最佳操作窗口.可为推进剂混合工艺优化提供依据.
To reveal safety mechanisms and mixing outcomes during the mixing process of composite propellant slur-ry in a vertical mixer,a steady-state model of homogeneous single-phase fluid was established using the computational fluid dynamics(CFD)method.The changes in key parameters such as pressure,temperature,shear stress,torque,and mixed flow field for twelve operating conditions with different slurry viscosities(331.342-1 260.216 Pa·s)and blade speeds(42.50-85.00 r/min)operating conditions were systematically simulated and analyzed.The results show that viscosity and rotational speed are significantly positively correlated with pressure,shear stress,and torque.Under the high parameter conditions of 1 260.216 Pa·s and 85 r/min,the maximum shear stress reaches 6.867 MPa,far exceeding the critical safety threshold of 3.180 MPa,while the temperature rise is limited(up to61.66℃).It indicates that the risk of thermal accumulation is limited under this operating condition,and the mechanical shear effect is more worthy of attention.Seven high-risk operating conditions were identified,mainly focused on high viscosity and high speed conditions.The mixing out-comes were evaluated by quantifying dead zone ratio,flow field coverage,and axial circulation efficiency.It was found that increasing the rotational speed can significantly improve the uniformity and efficiency of the mixing,but it will also increase safety risks simultaneously.Furthermore,the balance index was used to couple safety and mixing performances,and the optimal operating window that balances safety and efficiency has been identified.It can provide a basis for optimizing the mixing process of propellants.
牛踏雪;刘希亮;彭旭;饶国宁
南京理工大学安全科学与工程学院(江苏 南京,210094)南京理工大学安全科学与工程学院(江苏 南京,210094)南京理工大学安全科学与工程学院(江苏 南京,210094)南京理工大学安全科学与工程学院(江苏 南京,210094)
化学化工
复合推进剂混合安全CFD模拟
composite propellantsafety in mixing processCFD simulation
《爆破器材》 2026 (5)
33-42,10
评论