TA15钛合金热变形模型及组织演变规律研究OA
Study on Hot Deformation Modelling and Microstructure Evolution of TA15 Titanium Alloy
采用等温热压缩实验,在变形温度820~970 ℃、应变速率0.001~1.000 s-1范围内,系统研究了 TA15钛合金的热变形行为及微观组织演变规律.真应力-应变曲线呈现典型的流动软化特征,流动应力随变形温度升高而降低,随应变速率升高而增大.建立了考虑应变补偿效应的Arrhenius型本构模型,预测值与实验值的相关系数R=0.990,平均相对误差绝对值AARE=8.26%,在0.001~1.000 s-1应变速率范围内具有良好预测能力.基于动态材料模型构建了热加工图,明确了 820~860 ℃、0.1~1.0 s-1为失稳区,该区域对应高应变速率下再结晶受抑、核平均取向差值异常升高的微观组织特征.EBSD分析表明,820 ℃时以不连续动态再结晶为主导,形成"项链状"等轴细晶;随温度升高至960~970 ℃,演变为全片层组织;在近相变点高温侧,降低应变速率至0.001~0.010 s-1有利于获得均匀粗大的全片层组织,而提高应变速率至0.1~1.0 s-1则能保留更多等轴α相并细化β晶粒(由>100 μm细化至~15 μm).
The hot deformation behavior and microstructure evolution of TA 15 titanium alloy were systematically investigated via isothermal hot compression tests conducted at deformation temperatures ranging from 820 to 970℃ and strain rates ranging from 0.001 to 1.000 s-1.The true stress-strain curves exhibit typical flow softening characteristics,with flow stress decreasing with increasing temperature and increasing strain rate.A strain-compensated Arrhenius-type constitutive model is established,with a good predictive ability,a correlation coefficient(R)of 0.990 and an average absolute relative error(AARE)of 8.26%over the strain rate range of 0.001~1.000 s-1.On the basis of the dynamic materials model(DMM),heat-processing maps were constructed,identifying the instability domain at 820~860℃/0.1~1.0 s-1,which corresponds to the microstructural features of suppressed recrystallization and abnormally elevated KAM values at high strain rates.EBSD analysis reveals that discontinuous dynamic recrystallization(DDRX)dominates at 820℃,resulting in the formation of a necklace-like equiaxed fine-grained structure.As the temperature increases to 960~970℃,the microstructure evolves into a fully lamellar structure.At temperatures near the β-transus,decreasing the strain rate to 0.001~0.010 s-1 favours the formation of a uniform and coarse fully lamellar structure,whereas increasing the strain rate to 0.1~1.0 s-1 results in the retention of more equiaxed α phase and refined β grains(from>100 μm to~15 μm).
杨宏伟;刘家奥;李昌;郭良刚;杨岩峰
西北工业大学凝固技术全国重点实验室,陕西西安 710072||江西景航航空锻铸有限公司,江西景德镇 333400陕西天成航空材料股份有限公司,陕西咸阳 712023陕西天成航空材料股份有限公司,陕西咸阳 712023西北工业大学凝固技术全国重点实验室,陕西西安 710072西北工业大学凝固技术全国重点实验室,陕西西安 710072
矿业与冶金
TA15钛合金热变形本构模型热加工图动态再结晶
TA15 titanium alloyhot deformationconstitutive modelprocessing mapdynamic recrystallization
《铸造技术》 2026 (8)
912-925,14
评论