首页|期刊导航|智能化农业装备学报(中英文)|基于Carsim与MATLAB/Simulink联合仿真的犁耕作业拖拉机驱动轮滑转控制研究

基于Carsim与MATLAB/Simulink联合仿真的犁耕作业拖拉机驱动轮滑转控制研究OA

Research on drive wheel slip ratio control of a tillage tractor based on co-simulation with CarSim and MATLAB/Simulink

中文摘要英文摘要

为满足拖拉机田间犁耕作业过程中驱动防滑的需求,针对"拖拉机—犁具—土壤"的时变强非线性特征,研究提出一种基于Carsim与MATLAB/Simulink的拖拉机犁耕机组动力学建模与联合仿真方法,设计以电液比例方向阀为控制对象的滑转率控制系统,开发用于验证滑转率控制效果的硬件在环仿真平台.首先,基于东方红LX1804拖拉机车身参数,分别在Carsim和MATLAB/Simulink中建立拖拉机动力学和犁耕作业机组模型,开展联合仿真.然后,以电液比例方向阀为控制对象,以最优滑转率 sobj=0.16为控制目标,设计 PID控制器,并采用遗传算法对 PID参数进行整定.最后,基于dSPACE硬件在环仿真平台和IMC T3654控制器,开发用于验证滑转率控制效果的硬件在环仿真平台.联合仿真结果符合拖拉机田间实际作业情况,验证联合仿真模型的合理有效性;GA-PID控制方法下驱动轮滑转率控制误差波动范围为0.007,平均值为0.161,标准差为0.001,较传统PID控制具有更小的控制超调量,控制效果更好;在土壤比阻阶跃变化的工况下,联合仿真模型的动态响应和控制效果与离线仿真结果趋势一致,控制误差波动范围为0.007,平均值为0.161,标准差为0.001.仅在土壤比阻阶跃变化时和峰值处有细微差异,其差异值的数量级为10-4,在实际应用过程中具有可接受性.研究提出的基于Carsim与MATLAB/Simulink联合仿真的犁耕作业拖拉机驱动轮滑转控制方法,能够有效实现拖拉机犁耕作业过程中的驱动轮滑转控制,为拖拉机犁耕作业工况下的驱动防滑控制系统开发提供一定的理论参考和技术支持.

To satisfy the requirement of active anti-slip control for tractors under plowing conditions,this paper develops a dynamic modeling and co-simulation framework for tractor-plow assemblies to characterize the time-varying and strongly nonlinear"tractor-plow-soil"coupling system.A slip ratio control system is designed with an electro-hydraulic proportional directional valve as the control object,and a hardware-in-the-loop(HIL)simulation platform is developed to verify the effectiveness of the slip ratio control.First,based on the body parameters of the Dongfanghong LX1804 high-power tractor,vehicle dynamics and plowing operation models are established in CarSim and MATLAB/Simulink,respectively,and then coupled for joint simulation.Second,a PID controller is formulated targeting an optimal slip ratio of sobj=0.16,with genetic algorithm(GA)parameter tuning to optimize dynamic response.Finally,the control algorithm is deployed on an IMC T3654 real-time controller integrated with the dSPACE platform to complete the HILS verification system.The joint simulation results align with actual operational conditions,validating the rationality and effectiveness of the coupled simulation model.Under the GA-PID control method,the fluctuation range of the slip ratio is 0.007,with a mean value of 0.161 and a standard deviation of 0.001,demonstrating smaller control overshoot and better performance compared to the traditional PID control method.The hardware-in-the-loop testing shows that under soil resistivity step-change conditions,the model dynamic response and control effects are consistent with the offline simulation results.The control error fluctuation range is 0.007,with an average value of 0.161 and a standard deviation of 0.001.There are only slight differences at the moments of soil resistivity step changes and peak values,with the magnitude of the differences on the order of 10-4,which is acceptable for practical applications.The tractor drive wheel slip control method based on joint simulation using Carsim and MATLAB/Simulink proposed in this study can effectively control the slip ratio of the tractor driving wheels during tillage operations,providing a reference for slip control in tractor plowing tasks.

温景明;罗岩青;弓寒冬;田智辉;高春茹;陈雨;张硕

西北农林科技大学机械与电子工程学院,陕西 杨凌,712100西北农林科技大学机械与电子工程学院,陕西 杨凌,712100西北农林科技大学机械与电子工程学院,陕西 杨凌,712100陕西省农业机械研究所有限公司,陕西 咸阳,712000延安市宝塔区农机技术推广服务中心,陕西 延安,716000西北农林科技大学机械与电子工程学院,陕西 杨凌,712100西北农林科技大学机械与电子工程学院,陕西 杨凌,712100

农业科技

拖拉机犁耕作业联合仿真驱动轮滑转控制GA-PID控制硬件在环仿真

tractor plowing operationco-simulationdrive wheel slip controlGA-PID controlhardware-in-the-loop simulation

《智能化农业装备学报(中英文)》 2026 (3)

19-29,11

国家自然科学基金青年项目(32201677) National Natural Science Foundation of China(NSFC)Youth Project(32201677)

10.12398/j.issn.2096-7217.2026.03.002

评论