Mg-Al-Ca-Mn镁合金在热轧过程中的再结晶行为及其组织调控工艺OA
Recrystallization Behavior and Microstructural Control During Hot Rolling of Mg-Al-Ca-Mn Magnesium Alloy
本文以Mg-1Al-0.3Ca-0.5Mn镁合金(AXM10305)为研究对象,研究均匀化冷却方式与轧制变形参数对热轧过程中组织演化及再结晶行为的影响.合金经500 ℃×4 h均匀化处理后,采用水冷与炉冷调控初始第二相分布,并在300 ℃条件下进行多道次热轧变形.通过OM、SEM、EBSD及室温拉伸测试,分析不同工艺条件下的变形组织特征、再结晶相关演化行为及力学性能.结果表明:均匀化冷却方式显著影响Ca-富集第二相的分布特征,并进一步改变热轧过程中的变形组织与再结晶演化趋势;在相同轧制条件下,炉冷样品强度较高而塑性降低.随着累积变形量增加,合金中再结晶相关组织特征逐步显现,织构强度发生明显变化,材料强度与延伸率呈现出不同程度的协同变化.上述结果表明,在再结晶受到显著抑制或仅处于初始发生阶段的热轧工艺窗口内,通过调控均匀化冷却方式与轧制变形参数,可有效影响AXM10305镁合金的组织演化特征及再结晶倾向,并进一步影响其力学性能.
This study investigated the effects of homogenization cooling routes and rolling deformation parameters on microstructural evolution and recrystallization behavior during hot rolling of a Mg-1Al-0.3Ca-0.5Mn Mg alloy(AXM10305).After homogenization at 500℃ for 4 h,water cooling and furnace cooling were employed to tailor the initial distribution of second-phase particles,followed by multi-pass hot rolling at 300℃.The deformation microstructures,recrystallization-related evolution,and mechanical properties under different processing conditions were systematically characterized using OM,SEM,EBSD,and room-temperature tensile testing.The results demonstrate that the homogenization cooling route markedly affects the distribution characteristics of Ca-rich second phases,which in turn alters the deformation microstructure and recrystallization evolution during hot rolling.Under identical rolling conditions,furnace-cooled samples exhibit higher strength but reduced ductility compared with water-cooled counterparts.With increasing cumulative deformation,recrystallization-related microstructural features gradually develop,accompanied by pronounced changes in texture intensity,leading to different degrees of strength-ductility coordination.These results indicate that,within a hot-rolling processing window where recrystallization is significantly suppressed or only at its initial stage,the microstructural evolution characteristics and recrystallization tendency of the AXM 10305 Mg alloy can be effectively tailored by controlling the homogenization cooling route and rolling deformation parameters,thereby further influencing its mechanical properties.
吴泽霖;徐超;唐光泽;张旭;张明全
哈尔滨工业大学材料科学与工程学院,哈尔滨 150001哈尔滨工业大学材料科学与工程学院,哈尔滨 150001哈尔滨工业大学材料科学与工程学院,哈尔滨 150001哈尔滨工业大学材料科学与工程学院,哈尔滨 150001哈尔滨工业大学材料科学与工程学院,哈尔滨 150001
矿业与冶金
镁合金双模组织均匀化处理轧制
Magnesium alloyBimodal structureHomogenizationRolling
《宇航材料工艺》 2026 (4)
101-108,8
国家自然科学基金(52220105003)资助
评论