首页|期刊导航|陶瓷学报|铅含量和孔隙率对Li2TiO3陶瓷氘氚释放特性的影响

铅含量和孔隙率对Li2TiO3陶瓷氘氚释放特性的影响OA

Effects of Pb Content and Porosity on Deuterium and Tritium Release Peculiarities of Li2TiO3 Ceramics

中文摘要英文摘要

Li2TiO3陶瓷是聚变堆候选固态氚增殖材料.铅与氢同位素亲和力低,可促使氚在较低的温度下释放,降低陶瓷中的氚滞留率.本研究中,通过溶液燃烧合成的方式,制备了 Li2TiO3-5%Pb与Li2TiO3-10%Pb粉体.向粉体中添加不同比例的聚乙烯醇溶液并控制含量,制备了孔隙率为7.6%、10.1%和13.4%的陶瓷烧结体.对所制备的陶瓷样品进行了高温氘气暴露实验,暴露温度为573 K、暴露时间为4 h.对氘气暴露后的样品进行了升温热脱附实验,得到HD、HDO和D2O的热脱附图谱(TDS).在本研究中,D2的影响忽略不计,因此用HD代指氘气,HDO和D2O分别为氘代水(半重水)和氘水(重水).氘-TDS图谱显示,HD在900 K附近释放.HDO和D2O的释放温度均在700 K附近,释放温度低于HD.Li2TiO3-10%Pb的氘释放温度低于Li2TiO3-5%Pb,说明Pb添加能够促使氘在低温释放.对于不同孔隙率陶瓷,氘气-TDS图谱存在一个明显的主峰.TDS图谱显示,随着孔隙率的增大,600 K的氘释放速率明显下降.对陶瓷微球进行了中子辐照及释氚实验,释氚图谱显示,铅含量增至10%后,氚-TDS图谱向低温侧偏移.

[Background and purposes]Fusion energy is regarded as a clean,efficient and sustainable alternative energy source.The development of reliable solid-state tritium breeding materials is a key requirement for the application of fusion energy.Lithium titanate(Li2TiO3)ceramic is a promising tritium breeding material,owing to its high chemical inertness and structural stability,as compared with Li2O.Lead(Pb)has a low affinity for hydrogen isotopes,which is expected to reduce tritium retention and promote tritium release at lower temperatures.Pb is also a neutron multiplier,which can offer additional neutrons based on the(n,2n)reaction.Therefore,the introduction of Pb into the Li2TiO3 ceramic body would improve the tritium release properties,e.g.,decrease of tritium desorption temperature and increase of tritium desorption rate.In addition,the porosity of ceramic materials also affects the diffusion and release of tritium.This study was aimed to study the effects of Pb content and porosity on tritium release behavior of Li2TiO3 ceramics,providing an experimental basis for the design of tritium breeding lithium ceramics. [Method]Li2TiO3-5%Pb and Li2TiO3-10%Pb powders were synthesized by using solution combustion method,which is a simple,efficient and low-cost powder preparation technology.To adjust the porosity of ceramic sintered bodies,different proportions of polyvinyl alcohol(PVA)solutions were added to the powders as pore-forming agents.The PVA content was precisely controlled to prepare three groups of ceramic sintered bodies,with porosities of 7.6%,10.1%,and 13.4%.The prepared ceramic samples were subjected to high-temperature deuterium gas exposure experiments at 573 K for 4 h to simulate the tritium absorption process in fusion reactors.After deuterium exposure,thermal desorption spectroscopy(TDS)measurements were carried out at a heating rate of 10 K·min-1,resulting in the TDS spectra of HD,HDO and D2O.Besides,the Li2TiO3-Pb ceramic pebbles were introduced into the Kyoto University Research Reactor(KUR)to perform the neutron irradiation experiment.KUR is a light-water moderated tank-type reactor.For this experiment,the KUR was operated at 1 MW and the Pn-2 pneumatic system was used to transport the ceramic samples into the reactor core.The thermal neutron flux is 5.5× 1012 n·cm-2·s-1,the fast neutron flux is 1.2×1012 n·cm-2·s-1,and the epithermal neutron flux is 2.2×1011 n·cm-2·s-1.After neutron irradiation,the samples were transported to Shizuoka University.The tritium release experiment was performed using the tritium-TDS system.The tritium release was recorded by using proportional counters,while the release amount was measured by using liquid scintillation counters. [Results]According to deuterium TDS results,the HD release peak appeared at at 900 K,while the release temperature of HDO and D2O was 700 K.The HD is a gas form of deuterium,while HDO and D2O are water forms of deuterium.The desorption temperatures of HDO and D2O were significantly lower than that of HD,indicating that deuterium in the form of water molecules is easier to desorb at lower temperatures.For ceramic samples with different Pb contents,the deuterium desorption temperature of Li2TiO3-10%Pb was lower than that of Li2TiO3-5%Pb,confirming that the increase of Pb content can further promote tritium release at lower temperatures.For ceramics with different porosities,the TDS spectra of deuterium gas showed a distinct main peak,while the TDS spectra of deuterium water had two release peaks at 460 K and 600 K.The release rate on the high-temperature side decreased significantly with the increase in porosity.Neutron irradiation experiments showed that when the Pb content was increased to 10%,tritium started to desorb at low temperature.The tritium desorption rate was slightly increased.The tritium production rate per unit volume was expected to increase because tritium is heavy. [Conclusions]The chemical and structural properties of Li2TiO3-Pb can be controlled using the solution combustion synthesis method.The introduction of Pb can effectively reduce the tritium release temperature and promote tritium release at lower temperatures.The deuterium desorption rate as gas-form HD can be increased by the addition of Pb.The deuterium desorption shifts to a lower temperature range.Porosity has a significant impact on both water-form and gas-form deuterium desorption.The deuterium desorption from lithium ceramics in the high-temperature range can be reduced.For the tritium release,the addition of Pb facilitates the tritium desorption at low temperatures.The tritium release generation amount per unit volume can be expected.The tritium retention rate can be reduced by the addition of Pb.

浦一明;冯冠霖;大矢恭久;周启来

武汉理工大学材料科学与工程学院 湖北武汉 430070武汉理工大学材料科学与工程学院 湖北武汉 430070静冈大学理学部,日本静冈422-8529武汉理工大学材料科学与工程学院 湖北武汉 430070

化学化工

氚增殖剂钛酸锂氢同位素氘孔隙率

tritium breederlithium titanatehydrogen isotopedeuteriumporosity

《陶瓷学报》 2026 (4)

771-778,8

国家自然科学基金(12475303).

10.13957/j.cnki.tcxb.2026.04.010

评论