PIP-RMI复合工艺制备Cf/SiC-B4C复合材料的PyC/BN界面特征及其力学性能OA
Properties of Cf/SiC-B4C Composites Fabricated with PIP-RMI Combined Process
Cf/SiC-B4C复合材料作为一种兼具优异高温力学与抗氧化性能的热结构与热防护材料,在航空航天领域得到广泛应用.反应熔渗法(RMI)制备Cf/SiC-B4C复合材料虽能实现快速致密化,但其高温熔渗过程不仅易对碳纤维造成损伤,还会在基体中引入大量残余硅,导致复合材料力学性能下降.针对上述不足,本研究通过化学气相沉积结合浸涂-原位氮化法,在碳纤维表面制备了 PyC/BN双界面层,采用平板热压固化成型,结合前驱体浸渍裂解(PIP)与RMI的复合工艺,制备了不同成型压力的Cf/SiC-B4C复合材料.通过X射线衍射仪、X射线光电子能谱仪、阿基米德排水法、万能试验机、扫描电子显微镜对Cf/SiC-B4C复合材料的物相组成、性能和微观结构进行表征.结果表明:PyC/BN双界面层的引入不仅有效缓解了反应熔渗过程中熔融硅对碳纤维的侵蚀损伤,而且形成了良好的弱界面效应,使得复合材料在受力断裂时展现出明显的界面脱黏和纤维拔出现象.预制体的成型压力对孔隙结构和复合材料的力学性能影响显著,当成型压力为6 MPa时,经5次PIP循环后Cf/SiC-B4C预制体的体积密度达到1.73 g·cm-3,孔隙率降至12.9%,且复合材料在该压力下的力学性能达到最优,其抗弯强度与断裂韧性分别为234 MPa和7.5 MPa·m1/2,相比成型压力为2 MPa的复合材料,分别提升了 61.4%和74.4%.
[Background and purposes]Carbon fiber-reinforced silicon carbide(Cf/SiC)composites find extensive applications as advanced thermal structural and protection materials in the aerospace industry.They possess exceptional high-temperature mechanical properties,low density and high thermal shock resistance.However,a single SiC matrix shows inherent limitations under increasingly extreme environments.Incorporating secondary phases like boron carbide(B4C)modifies the matrix effectively.B4C offers high hardness and forms a protective borosilicate glass layer at high temperatures,which blocks oxygen diffusion.Therefore,Cf/SiC-B4C composites display broad application prospects.Researchers widely use reactive melt infiltration(RMI)to fabricate these composites,because it achieves rapid densification and near-net shape manufacturing.Nevertheless,the high-temperature molten silicon severely damages the carbon fibers during infiltration.Furthermore,incomplete reactions leave abundant brittle residual silicon in the matrix,which significantly degrades mechanical properties of the final composites.To overcome these critical shortcomings,a cost-effective and continuous pyrolytic carbon/boron nitride(PyC/BN)bilayer interphase were designed to protect the carbon fibers.Additionally,this study was aimed to optimize pore structure of the preforms by adjusting the molding pressure.By combining polymer infiltration and pyrolysis(PIP)with RMI,this methodology was intended to maximize carbon source introduction,minimize residual silicon and ultimately enhance the mechanical and fracture behaviors of the Cf/SiC-B4C composites. [Methods]The surface was treated by depositing a PyC/BN bilayer interphase onto polyacrylonitrile(PAN)-based 2D carbon fiber cloths.Initially,chemical vapor deposition(CVD)was used to synthesize the PyC inner layer at 1000 ℃,using methane as the carbon source.Subsequently,a combined dip-coating and in-situ nitridation method were employed to develope the BN outer layer.The PyC-coated fibers were immersed into an ethanol solution containing B4C powder and urea,followed by nitridation in a tube furnace at 1400 ℃ in nitrogen.For the composite fabrication,a planetary ball mill was employed to mix SiC powder,B4C powder,phenolic resin and graphite powder into a homogeneous slurry.The manufacturing process was to coat the interphase-modified fibers with this slurry and stacked them.A hot-pressing machine was used to cure the stacked preforms at 150 ℃ and four molding pressures,including 2 MPa,4 MPa,6 MPa and 8 MPa.After pyrolysis at 900 ℃,the PIP process was cyclized to infiltrate the porous preforms with a phenolic resin solution,until they showed no obvious weight gain.Finally,the RMI process densified the preforms at 1450 ℃ for 1 h using molten silicon.The element composition of the interface layer was measured by using XPS.An X-ray diffractometer was used to identify the phase composition.The Archimedes method was adopted to measure the bulk density and porosity.A universal testing machine was used to test the flexural strength and fracture toughness.Finally,a scanning electron microscope was used to characterize the microstructures and fracture morphologies. [Results]The CVD combined with the in-situ nitridation method can be used to successfully form a uniform PyC/BN bilayer interphase with a thickness of 232.8 nm.During nitridation,urea decomposes to generate ammonia,which reacts spontaneously with B4C at high temperatures to form a distinct granular BN outer layer.Regarding the preform architecture,the molding pressure significantly dictates the initial pore structure.Low pressure(2 MPa)leaves large inter-laminar voids,whereas excessive pressure(8 MPa)closes the pore channels prematurely.A molding pressure of 6 MPa creates an optimal highly interconnected porous network.Consequently,the 6 MPa preform exhibits the highest PIP densification efficiency,reaching a bulk density of 1.73 g·cm-3 and a low porosity of 12.9%after five PIP cycles.After the final RMI treatment,the 6 MPa Cf/SiC-B4C composite displayed the highest overall densification,exhibiting a bulk density of 2.24 g·cm-3 and a porosity of only 7.3%.X-ray diffraction confirms that the matrix primarily consists of SiC with minor amounts of B4C,C and residual Si.Notably,the 6 MPa sample displays the lowest residual silicon peak intensity.This indicates that its optimal pore structure facilitates the thorough reaction between molten silicon and the well-distributed PIP-derived carbon skeleton.The composites fabricated at 6 MPa possess the most outstanding mechanical properties.The flexural strength reaches 234 MPa,while the fracture toughness is 7.5 MPa·m1/2.Compared with the composites molded at 2 MPa,the two values increased by 61.4%and 74.4%,respectively.All samples exhibit pseudo-plastic fracture behaviors.The PyC/BN dual interphase effectively shields the carbon fibers from erosive molten silicon.Moreover,an ideal weak-interface effect was present,which induced massive interfacial debonding and extensive fiber pull-out during fracture.Conversely,the composites molded at 8 MPa show degraded mechanical performance,because the blocked pore channels restrict precursor infiltration,while excessive pressure induces microscopic damage to the carbon fibers. [Conclusions]In this study,a dual-layer PyC/BN interphase was successfully fabricated on carbon fibers via a combined chemical vapor deposition(CVD)and dip-coating/in-situ nitridation approach.Subsequently,Cf/SiC-B4C composites were manufactured using hot-press molding combined with a PIP-RM I process.The PyC/BN dual interphase played a crucial synergistic role in resisting melt infiltration damage and enhancing toughness.Specifically,the in-situ synthesized BN outer layer acted as a thermophysical barrier to effectively shield the carbon fibers from liquid silicon erosion during the RMI stage,while the inner PyC layer provided an appropriate interfacial bonding strength to dissipate fracture energy through interfacial debonding and fiber pull-out,thereby effectively averting brittle failure.Furthermore,the molding pressure significantly regulated the pore characteristics of the Cf/SiC-B4C preforms.At an optimal pressure of 6 MPa,the preform exhibited highly interconnected pore channels without distinct delamination,facilitating the infiltration of liquid precursors.After 5 PIP cycles,this optimized preform exhibited the highest bulk density(1.73 g·cm-3)and the lowest porosity(12.9%),providing an adequate carbon source for the subsequent RMI process.Conversely,an excessive pressure(8 MPa)led to severe pore closure,which hindered infiltration.Consequently,the Cf/SiC-B4C composite prepared at 6 MPa exhibited the minimum residual silicon content,a dense uniform matrix and a typical pseudo-plastic fracture behavior,achieving optimal mechanical properties with a flexural strength of 234 MPa and a fracture toughness of 7.5 MPa·m1/2.These values represent substantial improvements of 61.4%and 74.4%,respectively,as compared with the composite processed at 2 MPa.
薛龙博;陈建军
浙江理工大学材料科学与工程学院,浙江 杭州 310018浙江理工大学材料科学与工程学院,浙江 杭州 310018
通用工业技术
Cf/SiC-B4C复合材料PyC/BN双界面层PIP-RMI复合工艺热压成型成型压力力学性能
Cf/SiC-B4C compositesPyC/BN bilayer interphasePIP-RMI combined processmolding pressuremechanical properties
《陶瓷学报》 2026 (4)
741-752,12
国家自然科学基金(51872262).
评论