首页|期刊导航|青岛大学学报(自然科学版)|基于模块化的3D打印丝材收卷系统设计

基于模块化的3D打印丝材收卷系统设计OA

Design of Modular Winding System for 3D Printing Filament

中文摘要英文摘要

3D打印丝材收卷过程中存在自动化程度低、张力控制不精准等问题,基于模块化设计理念提出一种新型全自动收卷装置,通过选盘送盘模块、智能绕线模块、热熔封口模块和自适应剪断模块的协同控制,实现3D打印丝材收卷的全流程自动化;以STM32为核心构建分布式控制系统,结合比例、积分、微分参数调节控制(Proportional-Integral-Derivative Controller,PID)算法实现张力动态稳定调控;有限元分析验证核心部件(中心旋转支架)最大等效应力1.83 MPa,远低于材料屈服强度,位移量0.052 9 mm 满足刚度要求.实验结果表明,该系统张力控制精度达±0.05 kg,收卷速度可达15 m/min,椭圆度误差小于1.5%,适配1.75~3.0 mm直径的ABS、PLA、碳纤维等多种丝材,换盘响应时间小于10 s,连续运行24 h无故障,显著提升了收卷系统的自动化水平、稳定性与柔性适配能力.

During the winding process of 3D printing filament,there are problems such as low degree of automation and inaccurate tension control.Based on the modular design con-cept,a new type of fully automatic winding device was proposed.Through the collabora-tive control of the selection and feeding module of the reel,the intelligent winding mod-ule,the hot melt sealing module and the self-adaptive cutting module,the full process au-tomation of 3D printing filament winding was achieved.Build a distributed control system centered around STM32,and implement dynamic tension stabilization regulation by com-bining the Proportional-Integral-Derivative(PID)control algorithm.The finite element a-nalysis verifies that the maximum equivalent stress of the core component(central rotating bracket)is 1.83 MPa,which is far lower than the material yield strength,and the dis-placement of 0.052 9 mm meets the stiffness requirements.The experimental results show that the tension control accuracy of the system is±0.05 kg,the winding speed can reach 15 m/min,the ellipticity error is≤1.5%,and it is suitable for various filaments with diameters of 1.75~3.0 mm,such as ABS,PLA,and carbon fiber.The reel change response time is≤10 s,and there is no fault after continuous operation for 24 hours.This sig-nificantly improves the automation level,stability,and flexible adaptability of the winding sys-tem,providing a reliable solution for the efficient production of 3D printing filaments.

褚忠;刘铁一;刘少杰

上海应用技术大学机械工程学院,上海 201418上海应用技术大学机械工程学院,上海 201418上海应用技术大学机械工程学院,上海 201418

信息技术与安全科学

模块化设计3D打印丝材机械机构分布式控制系统收卷系统动态稳定调控

modular design3D printing filamentmechanical structuredistributed con-trol systemwinding systemdynamic stability regulation

《青岛大学学报(自然科学版)》 2026 (3)

46-51,77,7

10.3969/j.issn.1006-1037.2026.03.08

评论