首页|期刊导航|华南地质|上覆地层厚度对小位移走滑断裂分段性影响的有限元数值模拟

上覆地层厚度对小位移走滑断裂分段性影响的有限元数值模拟OA

Finite Element Numerical Simulation of the Influence of Overburden Thickness on the Segmentation of Small-displacement Strike-slip Faults

中文摘要英文摘要

[研究目的]塔里木盆地内的走滑断裂普遍具有位移小、断距有限、埋深大等特征,导致地震反射同相轴错断不明显,制约了其精细识别与构造解析.已有研究初步揭示上覆地层厚度对走滑断裂分段行为具有关键控制作用,但该因素与断裂分段长度、分段数量等参数间的关系及其力学调控机制仍有待深入解析.[研究方法]本文旨在通过数值模拟方法,初步揭示地层厚度与小位移走滑断裂分段长度的线性相关关系.为研究塔里木盆地顺北地区上覆地层厚度对走滑断裂分段模式的控制作用,本文构建了四组不同上覆地层厚度(2 km、3 km、4 km、5 km)的有限元模型,系统分析断裂数量、分段长度及应变分布随地层厚度的变化规律.[研究结果]模拟结果显示,上覆地层厚度对走滑断裂的分段性具有控制作用.随着地层厚度从 2 km 增加至5 km,断裂带数量由 6 条减少至 2 条,平均分段长度由 2.4 km 增大至 12.5 km,后二者分别与前者呈线性负相关和正相关关系.薄层中的断裂呈短分段、多分支特征,应变分散;厚层中的断裂应变能集中释放,形成长而连续的主干断裂.[结论]本研究明确了上覆地层厚度是控制走滑断裂分段长度的关键地质因素,建立了厚度‒分段长度模型.该模型从力学机制上解释了塔里木盆地走滑断裂纵向分层差异发育现象,表明厚度大的地层更有利于形成长分段、高连通性的断裂系统.研究成果为克拉通盆地内小位移走滑断裂的识别与预测提供了实验依据.

[Objective]Strike-slip faults in the Tarim Basin are generally characterized by small displacement,limited fault throw,and great burial depth.These features result in indistinct offset of seismic reflection events,which restricts their fine identification and structural analysis.Previous studies have preliminarily revealed that the thickness of overlying strata exerts a key control on the segmented behavior of strike-slip faults.However,the quantitative relationships between this factor and parameters such as fault segment length and segment number,as well as the corresponding mechanical governing mechanism,remain to be further explored.[Methods]This study aims to preliminarily reveal the linear correlation trend between stratigraphic thickness and the segment length of small-displacement strike-slip faults using numerical simulation.To investigate the control of overlying stratigraphic thickness on the segmentation pattern of strike-slip faults in the Shunbei area of the Tarim Basin,four groups of finite element models with different overlying stratigraphic thicknesses(2 km,3 km,4 km,and 5 km)were constructed.[Results]The variation laws of fault number,segment length,and strain distribution with stratigraphic thickness were systematically analyzed.Simulation results show that overlying stratigraphic thickness exerts a controlling effect on the segmentation of strike-slip faults.As the stratigraphic thickness increases from 2 km to 5 km,the number of fault zones decreases from 6 to 2,and the average segment length increases from 2.4 km to 12.5 km,showing a linear negative correlation and a linear positive correlation with stratigraphic thickness,respectively.In thin strata,faults are characterized by short segments and multiple branches with dispersed strain.In thick strata,strain energy is concentrated and released,forming long and continuous major faults.[Conclusions]This study confirms that overlying stratigraphic thickness is a key geological factor controlling the segment length of strike-slip faults,and establishes a thickness-segment length model.This model mechanically explains the vertically differential development of strike-slip faults in the Tarim Basin,indicating that thick strata are more conducive to the formation of fault systems with long segments and high connectivity.The research results provide an experimental basis for the identification and prediction of small-displacement strike-slip faults in cratonic basins.

池禹;张新松;朱素芹

东华理工大学 地球与行星科学学院,南昌 330013东华理工大学 地球与行星科学学院,南昌 330013东华理工大学 地球与行星科学学院,南昌 330013

天文与地球科学

走滑断裂有限元方法断层分段长度塔里木盆地

Tarim Basinstrike-slip faultfinite element methodfault segment length

《华南地质》 2026 (4)

588-601,14

江西省自然科学基金项目(20232BAB213086)

10.3969/j.issn.2097-0013.2026.04.003

评论