薄板高强钢激光-电弧复合焊非金属夹杂物及金相分析组织性能研究OA
Study on Non-Metallic Inclusions and Metallographic Analysis of Thin High-Strength Steel with Laser-Arc Hybrid Welding
以某型高强钢、EH36及CCSB船用钢为对象,采用金相法与扫描电镜(SEM/EDS)系统表征了4~6 mm薄板激光-电弧复合焊接头不同区域的非金属夹杂物特征,并对比分析了接头各微区(焊缝、熔合线、热影响区)的金相组织演变规律及其与力学性能的关联.结果表明:接头夹杂物主要为D类球状氧化物,尺寸集中在1~15 μm,金相法与SEM测试结果吻合良好;其中4 mm板厚接头各区域夹杂物平均尺寸略低于5 mm、6 mm板厚.焊接热输入对夹杂物数量无显著影响,但随热输入增大,夹杂物尺寸呈增大趋势、焊缝硬度相应降低.由于低热输入耦合焊丝/母材中的Ti、Nb微合金化元素,焊缝及热影响区获得以针状铁素体和细晶铁素体为主的均匀细小组织,显著优于传统埋弧焊的粗晶组织.接头拉伸断裂均发生于母材,弯曲试样无裂纹,综合力学性能优良.本研究建立了薄板高强钢激光-电弧复合焊接头"夹杂物特征-金相组织-力学性能"的系统性关联分析方法,为船舶制造等领域的高效高质量焊接工艺优化提供了技术支撑.
This study systematically characterizes non-metallic inclusions in different zones of 4-6 mm thin-plate laser-arc hybrid welded joints of a certain high-strength steel,EH36,and CCSB marine steels using metallographic methods and scan-ning electron microscopy(SEM/EDS).The microstructural evolution in the weld metal,fusion line,and heat-affected zone is comparatively analyzed,and its correlation with mechanical properties is established.The results show that the inclusions are predominantly type D spherical oxides,with sizes concentrated in the range of 1-15 μm;the metallographic and SEM re-sults are in good agreement.The average inclusion size in each zone of the 4 mm thick joint is slightly smaller than that in the 5 mm and 6 mm thick plates.Heat input does not significantly affect the number of inclusions,but increasing heat input tends to enlarge the inclusion size and consequently reduce the weld hardness.Owing to the low heat input and the presence of Ti and Nb microalloying elements in both the welding wire and the base metal,the weld metal and heat-affected zone de-velop a uniform and fine microstructure dominated by acicular ferrite and fine-grained ferrite,which is markedly superior to the coarse-grained structure obtained by conventional submerged arc welding.All tensile specimens fractured in the base metal,and bending specimens showed no cracks,indicating excellent overall mechanical properties.This work establishes a systematic correlation framework linking inclusion characteristics,microstructure,and mechanical properties for laser-arc hybrid welded thin high-strength steel joints,providing technical support for optimizing high-efficiency and high-quality welding processes in shipbuilding and related industries.
何春华;刘镇;潘喜春;张标;钟美达;卢晓丹
中船黄埔文冲船舶有限公司 广东省舰船先进焊接技术重点实验室,广东 广州 510715中船黄埔文冲船舶有限公司 广东省舰船先进焊接技术重点实验室,广东 广州 510715中船黄埔文冲船舶有限公司 广东省舰船先进焊接技术重点实验室,广东 广州 510715中船黄埔文冲船舶有限公司 广东省舰船先进焊接技术重点实验室,广东 广州 510715中船黄埔文冲船舶有限公司 广东省舰船先进焊接技术重点实验室,广东 广州 510715中船黄埔文冲船舶有限公司 广东省舰船先进焊接技术重点实验室,广东 广州 510715
矿业与冶金
薄板高强钢激光-电弧复合焊热输入非金属夹杂物金相组织力学性能
thin high-strength steellaser-arc hybrid weldingheat inputnon-metallic inclusionsmetallographic structuremechanical properties
《电焊机》 2026 (9)
93-104,12
广东省重点科技计划项目(2023B1212070026)
评论