不同压制参数下PBX粉末成型质量的仿真分析OA
Simulation Analysis of Forming Quality of PBX Powder under Different Pressing Parameters
为优化高聚物粘结炸药(polymer bonded explosive,PBX)压制参数,分析双向压制工艺参数对成型质量的影响规律.采用有限元模拟结合Shima-Oyane和剪切摩擦模型,对PBX粉末双向压制过程进行数值模拟研究,分析不同压制压力和保温温度对PBX粉末相对密度和等效应力的影响.仿真结果表明:相比于保温温度,压制压力对药柱的成型密度影响更大.在相同的保温温度下,提高压制压力,可以明显提升药柱的相对密度,并降低相对密度差;在相同的压制压力下,温度对相对密度和等效应力的影响较小.上、下冲头以相同的速度压制时,接近上、下冲头的水平面,边缘密度为 0.61 kg/m3,中心密度为 0.54 kg/m3;远离上、下冲头的水平面,边缘密度为 0.99 kg/m3,中心密度 0.97 kg/m3.
In order to optimize the pressing parameters of polymer bonded explosive(PBX),the influence of bidirectional pressing process parameters on molding quality was analyzed.The bidirectional compaction process of PBX powder was numerically simulated by finite element method combined with Shima-Oyane and shear friction model,and the effects of different compaction pressures and holding temperatures on the relative density and equivalent stress of PBX powder were analyzed.The simulation results show that the compacting pressure has a greater influence on the forming density of the grain than holding temperature.At the same holding temperature,the relative density of the grain can be significantly increased and the relative density difference can be reduced by increasing the pressing pressure;at the same pressing pressure,the temperature has little effect on the relative density and the equivalent stress.When the upper and lower punches are pressed at the same speed,the edge density is 0.61 kg/m3 and the center density is 0.54 kg/m3 on the horizontal plane close to the upper and lower punches,and the edge density is 0.99 kg/m 3 and the center density is 0.97 kg/m3 on the horizontal plane far away from the upper and lower punches.
王勇;杨治林;郭进勇;伍凌川;李昂;余瑶;胡才旺;李旭东
中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000||南京理工大学化学与化工学院,南京 210094中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000中国兵器装备集团自动化研究所有限公司智能制造事业部,四川 绵阳 621000
军事科技
双向压制压制参数数值模拟相对密度
bidirectional compressioncompression parametersnumerical simulationrelative density
《兵工自动化》 2026 (9)
24-29,35,7
评论