断层滑移作用下采油井套管力学行为及影响因素研究OA
Study on Mechanical Behavior and Influencing Factors of Production Well Casing under Fault Slip
断层滑移会使采油井套管承受复杂的剪切、挤压与弯曲载荷,常导致套管发生错断及弯曲变形,是威胁井筒完整性及油井寿命的主要套损形式之一.为解决此类问题并做好相应的预防措施,本文建立了断层作用下地层-水泥环-套管三维数值耦合模型,分析断层位移、地层弹性模量、地层泊松比及套管内压对套管应力与应变的影响.结果表明:随断层位移增加,套管由"S"型形变发展为"Z"型屈曲,应力与应变显著增大,最大应变增幅达11倍;地层弹性模量增大时,断层上方受压侧应力大幅减小,最大降幅70.3%,下方应力增大,应变随弹性模量增加而增大,其中最大增幅2.6倍;地层泊松比对套管应力应变呈非线性影响,低泊松比为0.25时断层处出现明显压应变突变0.018,发生显著屈曲;套管内压影响复杂,远离断层位置应力随内压增大而增大,断层附近应力应变呈现先增后降或持续减小等规律.基于上述分析,断层位移是套管失稳的主控因素,而地层弹性模量、泊松比及内压通过非线性耦合机制显著调控其应力应变响应,工程中需针对断层带进行差异化抗屈曲设计.
Fault slip can subject production well casing to complex shear,compression,and bending loads,often leading to casing dislocation and bending deformation,which constitutes one of the major casing damage modes threatening wellbore integrity and oil well life.To address this issue and implement appropriate preventive measures,this paper establishes a three-dimensional numerical coupling model of the formation-cement sheath-casing system under faulting,and analyzes the effects of fault displacement,formation elastic modulus,formation Poisson's ratio,and casing internal pressure on casing stress and strain.The results indicate that,as fault displacement increases,the casing deformation evolves from an"S"shape to a"Z"shape buckling,with significant increases in stress and strain,and the maximum strain amplification reaches 11 times.When the formation elastic modulus increases,the stress on the compression side above the fault decreases substantially,with a maximum reduction of 70.3%,while the stress below the fault increases,and the strain increases with the elastic modulus,with a maximum amplification of 2.6 times.The formation Poisson's ratio exhibits a nonlinear influence on casing stress and strain,at a low Poisson's ratio of 0.25,an obvious compressive strain mutation of 0.018 occurs at the fault location,indicating significant buckling.The effect of casing internal pressure is complex:away from the fault location,stress increases with internal pressure,while near the fault,stress and strain exhibit patterns of initial increase followed by decrease or continuous reduction.Based on the above analysis,fault displacement is the dominant controlling factor for casing instability,while formation elastic modulus,Poisson's ratio,and internal pressure significantly regulate the stress-strain response through a nonlinear coupling mechanism.In engineering practice,differentiated anti-buckling designs should be implemented for fault zones.
周振寰;张向阳;刘智泉;胡世伟;康玉阳;杨云
中国石化股份有限公司江苏油田分公司采油一厂,江苏扬州 225009中国石化股份有限公司江苏油田分公司采油一厂,江苏扬州 225009中国石化股份有限公司江苏油田分公司采油一厂,江苏扬州 225009中国石化股份有限公司江苏油田分公司采油一厂,江苏扬州 225009中国石化股份有限公司江苏油田分公司采油一厂,江苏扬州 225009西南石油大学机电工程学院,成都 610500
能源科技
走滑断层套管应力应变内压
strike-slip faultproduction casingstressstraininternal pressure of casing
《能源研究与管理》 2026 (3)
54-62,9
江苏油田科研项目"井筒重建优化工艺应用"
评论