首页|期刊导航|金属加工(热加工)|燃煤发电锅炉激光-TIG复合焊接工艺及腐蚀性能试验分析

燃煤发电锅炉激光-TIG复合焊接工艺及腐蚀性能试验分析OA

Experimental analysis of laser-TIG composite welding process and corrosion performance of coal-fired power generation boilers

中文摘要英文摘要

燃煤发电锅炉在工作时产生的腐蚀性介质会在焊接接头表面形成氧化皮和腐蚀产物,导致接头强度降低.为提升燃煤发电锅炉焊接接头质量,降低焊接接头腐蚀速率,进行燃煤发电锅炉激光-TIG复合焊接工艺及腐蚀性能试验分析.选用SA213-T23新型铁素体耐热钢,采用激光-TIG复合焊接工艺,以YAG固体脉冲激光与旁轴式TIG电弧为热源,分别设置激光功率为300W、350W、400W及450W进行焊接,焊接完成后,测试试件基础力学性能及耐腐蚀性能.结果表明:适度增加激光功率可提升接头强度,400W时焊缝基础力学性能可达最佳水平;且该激光功率下焊接试件在电化学腐蚀、晶间腐蚀及不同介质浸泡腐蚀试验中,腐蚀电位最高、腐蚀电流最小,自腐蚀电流、自腐蚀电位和钝化电流均优于其他功率试件;同时,其质量损失最小,弯折后无裂纹产生;在不同质量分数的H2SO4和NaOH溶液浸泡过程中,400W试件的腐蚀速率始终保持最低.因此,当激光功率为400W时,可有效保证燃煤发电锅炉焊接接头质量.

The corrosive medium generated by coal-fired power boilers during operation will form oxide scale and corrosion products on the surface of welding joints,resulting in a decrease in joint strength.To improve the quality of welding joints in coal-fired power generation boilers and reduce the corrosion rate of welding joints,laser TIG composite welding technology and corrosion performance test analysis were conducted for coal-fired power generation boilers.The new type of ferritic heat-resistant steel SA213-T23 was selected.The laser-TIG composite welding process was adopted,with YAG solid-state pulsed laser and paraxial TIG arc as the heat sources.The laser power was set at 300W,350W,400W and 450W respectively for welding.After the welding was completed,the basic mechanical properties and corrosion resistance of the specimens were tested.The results show that moderately increasing the laser power can improve the joint strength,and the basic mechanical properties of the weld reach the optimal level at 400W.Furthermore,for the welded specimens obtained at this laser power in electrochemical corrosion,intergranular corrosion and immersion-corrosion tests in different media,the specimen presents the highest corrosion potential and the lowest corrosion current,with its self-corrosion current,self-corrosion potential and passivation current superior to those of specimens welded at other power levels.Meanwhile,its mass loss is minimal and no cracks occur after bending.During the soaking process in H2SO4 and NaOH solutions of different mass fractions,the corrosion rate of the 400W specimens remained the lowest all the time.Therefore,when the welding laser power is 400W,the quality of the welded joints of coal-fired power generation boilers can be effectively guaranteed.

阮小康

华电煤业集团有限公司 北京 102299

燃煤发电锅炉复合焊接腐蚀性能激光功率腐蚀电流腐蚀电位

coal-fired power generation boilercomposite weldingcorrosion performancelaser powercorrosion currentcorrosion potential

《金属加工(热加工)》 2026 (9)

80-87,8

评论