消防感应器面盖复合斜滑块机构模具设计OA
Design of injection mold with composite angled slider mechanism for a fire sensor face cover
针对某消防感应器面盖内部存在3个倒扣区及一处18 °斜坡扣边导致无法直接脱模的难题,设计了一模两腔注塑模具及一套复合斜滑块顺序抽芯机构.塑件平均壁厚3 mm,外形尺寸143 mm×34 mm×44 mm,体积34.3 cm³,选用PC/ABS合金以满足阻燃与强度要求.模具设计的核心在于解决内壁倒扣的协同脱模问题.为此,将3个倒扣区的成型部分分别设计为3个独立滑块,并集成于一个承载滑块上.脱模过程分两步:开模初期,斜导柱驱动第一个滑块沿斜向(与水平面夹角20 °)先行斜向抽芯,同时由弹簧驱动的第二、第三滑块沿2个互为相反的水平方向侧向抽芯18 mm;随后,延时斜导柱驱动承载滑块带动3个滑块整体沿第一滑块斜向抽芯方向移动,完成最终分离.CAE分析(Moldflow)验证了浇注系统与冷却系统的合理性:单腔充填时间1.54 s,最大压力45.3 MPa,翘曲变形量1.117 mm,流动前沿温度均匀,锁模力需求约65 t,熔接线风险可控.模具采用两板模结构,单次开模,推管顶出.该复合斜滑块机构将3个方向的复杂抽芯动作分解为顺序、可控的简单运动,结构紧凑,动作可靠.
A fire sensor face cover features three inner undercut regions and an 18° inclined flanged edge,which leads to severe difficulties in direct demolding during injection molding.To solve this problem,a dual-cavity injection mold equipped with a novel composite angled slider sequential core-pulling mechanism was proposed in this work.The target plastic part has an average wall thickness of 3 mm,overall dimensions of 143×34×44 mm3,and a volume of 34.3 cm3.A PC/ABS alloy was selected as the molding material to satisfy the requirements of flame retardancy and mechanical per-formance.The core difficulty of the mold design lies in the coordinated demolding of multiple internal undercut struc-tures.To address this issue,the molding inserts corresponding to the three undercuts were designed as three independent sliding blocks,which were integrally assembled on a shared carrier slider to realize synchronous cooperative motion.The overall demolding procedure was divided into two sequential stages.In the early mold-opening stage,an angled lifter drives the primary slider to complete the initial inclined core-pulling at an angle of 20° relative to the horizontal plane.Meanwhile,the secondary and tertiary sliders are actuated by springs to implement lateral core-pulling with a stroke of 18 mm in two opposite horizontal directions.Afterwards,a delayed angled lifter pushes the carrier slider together with all three sliders to integrally move along the inclined direction of the first core-pulling action,achieving complete separation between the mold and the plastic part.Moldflow CAE simulation was conducted to verify the rationality of the designed gating and cooling systems.The simulation results show that the single-cavity filling time is 1.54 s,the maximum injec-tion pressure is 45.3 MPa,and the maximum warpage deformation is 1.117 mm.The melt front temperature distribu-tion remains uniform throughout the filling process,the required clamping force is approximately 65 tons,and the risk of weld line defects is well controlled.The developed mold adopts a conventional two-plate structure with single parting sur-face and pin ejection.The proposed composite angled slider mechanism decomposes the complex three-dimensional multi-directional core-pulling motion into stepwise,controllable,and simple sequential movements.
贺柳操;唐志
湖南机电职业技术学院机械工程学院,长沙 410151长沙众耀模塑科技有限公司,长沙 410137
化学化工
消防感应器面盖复合斜滑块顺序抽芯延时抽芯模具设计
fire sensor face covercomposite angled slidersequential core-pullingdelayed core-pullingmold design
《中国塑料》 2026 (8)
126-133,8
评论