基于有限元计算的塑料双腔导管气辅挤出口模优化设计OA
Optimization design of a plastic double-lumen catheter extrusion die based on finite element simulation
采用PTT本构方程构建了塑料双腔导管三维黏弹挤出流动模型,运用有限元方法实现了稳定的数值求解,研究了4种不同气体辅助段长度下熔体流速、剪切速率和第一法向应力差等场量分布.并采用Realizable k-epsilon模型研究了不同气辅进气角度的气体流速分布.结果表明,较长的气体辅助段有利于提高制品质量,结合实际生产情况,确定5 mm的气体辅助段长度为最佳;较小的进气角度有利于改善气流状态,进而提升制品质量,结合实际可操作性,确定30゜的进气角度为最佳.基于气体辅助段长度和气辅进气角度的有限元计算结果,对双腔导管挤出口模进行了优化设计,并通过试验研究验证了设计方法的可靠性.
In this study,a three-dimensional viscoelastic extrusion flow model for plastic double-lumen catheters was es-tablished based on the PTT constitutive equation,and stable numerical solutions were obtained via the finite element method.The flow field distributions of velocity,shear rate,and first normal stress difference were analyzed under four different gas-assisted section lengths.The simulation results indicate that an extended gas-assisted section contributes to improved forming quality of catheter products.Combined with practical production requirements,a gas-assisted section length of 5 mm was determined as the optimal structural parameter.Furthermore,the realizable k-ε turbulence model was adopted to investigate the gas flow velocity distribution under different inlet angles.The results reveal that a smaller inlet angle optimizes the internal gas flow condition,which further enhances the overall product quality.Considering on-site operational feasibility,30° was selected as the optimal inlet angle.Based on the finite element simulation results of gas-assisted section length and inlet angle,the structural parameters of the double-lumen catheter extrusion die were opti-mized.The reliability of the proposed optimization method was further validated through experimental tests.
单义杰;刘强;纪海波;肖兵;邓小珍;张伟;祝志芳
江西水利电力大学机械工程学院,南昌 330099江西水利电力大学精密驱动与装备江西省重点实验室,南昌 330099江西水利电力大学精密驱动与装备江西省重点实验室,南昌 330099江西水利电力大学机械工程学院,南昌 330099||江西水利电力大学精密驱动与装备江西省重点实验室,南昌 330099江西水利电力大学机械工程学院,南昌 330099||江西水利电力大学精密驱动与装备江西省重点实验室,南昌 330099华东交通大学机电与车辆工程学院,南昌 330013江西水利电力大学机械工程学院,南昌 330099||江西水利电力大学精密驱动与装备江西省重点实验室,南昌 330099
化学化工
塑料双腔导管气辅挤出气辅段长度进气角度
plastic double-lumen cathetergas-assisted extrusionlength of gas-assisted sectioninlet angle
《中国塑料》 2026 (8)
120-125,6
江西水利电力大学国家级大学生创新创业训练计划资助项目(202511319008)南昌工程学院省级大学生创新创业训练计划资助项目(S202411319014)国家自然科学基金青年项目(52303038)江西省自然科学基金面上项目(20252BAC240139)
评论