铣削工艺参数对不同PLA基复合颗粒材料表面质量的影响OA
Effect of milling parameters on surface quality of 3D-printed PLA and PLA-based composite parts
针对聚乳酸(PLA)颗粒料3D打印后表面质量和尺寸精度较差的问题,采用铣削工艺来提高表面质量和尺寸精度.首先分析进给速度(Vf)、铣削深度(ap)和转速(n)3个因素对纯PLA材料的表面粗糙度(Ra)和毛刺高度(Rz)的影响,得出纯PLA材料的最佳铣削加工参数;应用该参数于聚乳酸/碳纤维(PLA/CF)和聚乳酸/石墨烯(PLA/Gr)复合材料打印;得出此复合材料的Ra和Rz变化规律.结果表明,铣削后,PLA的Ra由6.22 μm降至3.86 μm,PLA/CF的Ra由6.18 μm降至2.26 μm,PLA/Gr的Ra由4.4 μm降至0.96 μm,分别平均减少38%、63%和78%;铣削后,PLA的Rz从33.21 μm降至18.61 μm,PLA/CF的Rz从28.52 μm降至16.64 μm,PLA/Gr的Rz从24.23 μm降至14.68 μm,分别平均减少44%、42%和39%;选择合适的进给速度、铣削深度和转速,有利于提高颗粒材料打印样品的表面质量及相关性能.
To overcome the poor surface finish and low dimensional accuracy inherent in parts fabricated by pellet-based 3D printing,post-processing milling was employed as a finishing operation.In this study,the effects of feed rate(Vf),cutting depth(ap),and spindle speed(n)on surface roughness(Ra)and burr height(Rz)were systematically investigat-ed for neat PLA specimens,and the optimal parameter combination was identified.The optimized milling conditions were then applied to 3D-printed PLA/carbon fiber(CF)and PLA/graphite(Gr)composites,and the resulting varia-tions in Ra and Rz were characterized.Experimental results indicate that milling significantly improves surface quality.For neat PLA,Ra decreased from 6.22 to 3.86 μm(38%reduction);for PLA/CF composites,from 6.18 to 2.26 μm(63%reduction);and for PLA/Gr,from 4.4 to 0.96 μm(78%reduction).Burr height Rz also exhibited marked de-clines:neat PLA dropped from 33.21 to 18.61 μm(44%reduction),PLA/CF composites from 28.52 to 16.64 μm(42%reduction),and PLA/Gr composites from 24.23 to 14.68 μm(39%reduction).These findings demonstrate that appropriate selection of feed rate,cutting depth,and spindle speed can substantially enhance the surface quality and overall performance of additively manufactured polymer components.
梁雨心;钱波;刘彪强;陈治强
上海工程技术大学机械与汽车工程学院,上海 201600上海工程技术大学机械与汽车工程学院,上海 201600||机械工业航空大型复杂薄壁构件智能制造技术重点试验室,上海 201600上海工程技术大学机械与汽车工程学院,上海 201600上海工程技术大学机械与汽车工程学院,上海 201600
化学化工
颗粒料打印铣削加工工艺参数表面粗糙度复合材料
granular materialprintingmilling processprocess parametersurface roughnesscomposite
《中国塑料》 2026 (8)
77-85,9
国家重点研发计划项目(2018YFB1105300)
评论