首页|期刊导航|中国塑料|多壁碳纳米管与三氧化钨共混改性填充聚酰亚胺的摩擦学性能研究

多壁碳纳米管与三氧化钨共混改性填充聚酰亚胺的摩擦学性能研究OA

Tribological properties of polyimide modified with multi-walled carbon nanotubes and tungsten trioxide

中文摘要英文摘要

为提升聚酰亚胺(PI)的耐磨性能,开展了多壁碳纳米管(MWCNTs)与三氧化钨(WO3)分别物理混合与水热合成作为增强填料填充的PI复合材料性能研究.通过涂覆烧结制备PI复合材料,采用磨损试验机研究复合材料的摩擦学性能,探讨不同载荷与填料含量对复合材料性能的影响.结果表明,与纯PI和仅添加MWCNTs的PI相比,WO3和MWCNTs共混作为增强填料耐磨性能更好,其中WO3@MWCNTs含量为1%时耐磨性能最好,与PI相比,在100、200、300 N时摩擦因数和磨损率分别降低了33.3%、22.8%、4.7%和70.0%、58.6%、26.0%;与0.6%MWCNTs/PI相比,在100、200、300 N时摩擦因数和磨损率分别降低了11.5%、7.0%、0.9%和57.9%、43.6%、23.0%;相比物理混合,WO3和MWCNTs水热共混改性PI形成了更加均匀致密的转移膜,磨损表面光滑平整,表现为轻微磨粒磨损伴有疲劳磨损的混合磨损.

To enhance the wear resistance of polyimide(PI),PI composites reinforced with multi-walled carbon nano-tubes(MWCNTs)and tungsten trioxide(WO3)were fabricated via physical blending and hydrothermal synthesis in this study.The composite coatings were prepared through coating and sintering processes,and their tribological performance was systematically tested using a wear tester.The influences of applied load and filler content on the tribological proper-ties of the composites were comprehensively analyzed.The experimental results reveal that the hybrid addition of WO3 and MWCNTs endows PI composites with superior wear resistance compared with pure PI and single MWCNT-filled PI composites.The optimal tribological performance is obtained for the PI composite with 1 wt%WO3@MWCNT hybrid fillers.Under applied loads of 100 N,200 N,and 300 N,the optimal composite exhibits friction coefficient reductions of 33.3%,22.8%,and 4.7%,as well as wear rate reductions of 70.0%,58.6%,and 26.0%,respectively,com-pared with pure PI.Relative to the 0.6 wt%MWCNT/PI composite,its friction coefficient decreases by 11.5%,7.0%,and 0.9%,and its wear rate drops by 57.9%,43.6%,and 23.0%at the corresponding loads.Further-more,compared with physically blended fillers,WO3 and MWCNTs modified via hydrothermal treatment can form a more uniform and dense transfer film on the friction surface.This optimized microstructure contributes to a smooth and flat worn surface of the composite,and the wear behavior is dominated by a mixed wear mechanism consisting of mild abrasive wear and fatigue wear.

陈嘉泰;刘洪;吴建成;张宝鹏;崔军洋;何长存;张莉珍

兰州交通大学机电工程学院,兰州 730070兰州交通大学机电工程学院,兰州 730070兰州交通大学机电工程学院,兰州 730070兰州交通大学机电工程学院,兰州 730070兰州交通大学机电工程学院,兰州 730070兰州交通大学机电工程学院,兰州 730070兰州交通大学机电工程学院,兰州 730070

化学化工

水热反应三氧化钨聚酰亚胺摩擦学性能磨损机理

hydrothermal reactiontungsten trioxidepolyimidetribological propertywear mechanism

《中国塑料》 2026 (8)

17-22,6

10.19491/j.issn.1001-9278.2026.08.004

评论