融合IBFO-LuGre与降阶观测器的机床进给机构动态性能优化控制OA
Optimization Control of Dynamic Performance of Machine Tool Feed Mechanism Integrating IBFO-LuGre and Reduced Order Observer
机床进给机构的摩擦非线性易引发预滑动刚度突变与 Stribeck 负阻尼效应,导致速度过零区跟踪误差陡增及动态响应性能下降.为此,提出一种融合改进细菌觅食算法(IBFO)与降阶扩张状态观测器(RESO)的 LuGre 模型前馈补偿控制策略,实现对进给机构的动态性能优化控制.首先,建立进给机构的LuGre 摩擦模型,并采用 IBFO 算法分阶段优化模型静态与动态参数,实现对预滑动刚度突变及 Stribeck 效应的精准刻画.基于优化后的模型,设计前馈补偿力矩以实时抵消摩擦反向力矩,抑制速度过零区的跟踪误差.然后引入 RESO 在线估计由参数摄动及未建模动态引起的总扰动,并通过补偿电流实时抑制,消除Stribeck 负阻尼引发的振荡与相位滞后,最终在位置环与速度环实现近零超调与带宽显著提升,改善动态响应性能.实验结果表明:该方法显著提升了位置环与速度环的响应带宽和平稳性,超调量分别降至 0.14%和 0.09%,优于对比方法;在速度过零区,最大动态跟踪误差与速度波动率均显著降低,尤其在高速和极低速工况下表现优异;同时,在加减速复合轨迹工况下仍能保持极低的跟踪误差与速度波动率,有效增强了机床进给机构在动态工况下的鲁棒性与动态性能.
The frictional nonlinearity of the machine tool feed mechanism can easily cause sudden chan-ges in presliding stiffness and Stribeck negative damping effect,leading to sharp increases in tracking error within the velocity zero-crossing region and degradation of dynamic response performance.To address this issue,a feedforward compensation control strategy that integrates the LuGre friction model,optimized by an improved bacterial foraging optimization(IBFO)algorithm with a reduced-order extended state ob-server(RESO),is proposed to achieve dynamic performance optimization of the feed mechanism.Firstly,a LuGre friction model for the feed mechanism is established,and the IBFO algorithm is adopted to optimize the static and dynamic parameters of the model in a staged manner,enabling an accurate characterization of presliding stiffness variation and the Stribeck effect.Based on the optimized model,a feedforward compen-sation torque is designed to counteract the frictional reverse torque in real time and suppress the tracking errors in the zero-crossing zone of the speed.Then,a RESO is introduced to estimate the total disturbance caused by parameter perturbations and unmodeled dynamics online,which is further suppressed in real time through compensation current to eliminate oscillations and phase lag induced by Stribeck negative damp-ing.Consequently,near-zero overshoot and significant bandwidth improvement are achieved in both the position and velocity loops to substantially improve dynamic response performance.The experimental re-sults show that this proposed method significantly improves the response bandwidth and stability of the position and velocity loops,reducing overshoot to 0.14%and 0.09%,respectively,which is superior to the comparative methods.In the zero-crossing speed zone,the maximum dynamic tracking error and speed fluctuation rate are markedly reduced,with especially excellent performance under high-speed and ex-tremely low-speed operating conditions.Moreover,under the conditions of compound acceleration/decel-eration trajectory,the method maintains extremely low tracking error and speed fluctuation rate,effectively enhancing the robustness and dynamic performance of the machine tool feed mechanism under dynamic op-erating conditions.
张韬;谢丽
昆明铁道职业技术学院机电工程学院,云南 昆明 650208昆明铁道职业技术学院机电工程学院,云南 昆明 650208
矿业与冶金
机床进给机构LuGre模型改进细菌觅食算法降阶扩张状态观测器前馈补偿动态性能优化
machine tool feed mechanismLuGre modelimproved bacterial foraging optimizationre-duced-order extended state observerfeedforward compensationdynamic performance optimization
《机械与电子》 2026 (8)
73-81,9
云南省教育厅科学研究基金项目(2025J1848)
评论