55kg级低氢高韧性全位置药芯焊丝的研制与性能评价OA
Development and Performance Evaluation of a 550 MPa-Grade Low-Hydrogen,High-Toughness Flux-Cored Wire for All-Position Welding
针对海洋工程、桥梁及低温服役结构用55 kg级低合金高强钢焊接材料的低氢、高韧性和全位置焊接需求,采用钛碱型渣系和Mn-Si-Ni-Ti-B-RE多元合金体系制备直径1.2 mm的气体保护药芯焊丝,并通过钢带清洗、药粉分级烘焙和焊丝在线复烘干控制扩散氢含量.测试焊丝工艺性能、熔敷金属成分与力学性能、扩散氢含量、裂纹尖端张开位移(CTOD)和显微组织,并采用EH460钢板验证接头性能.结果表明,所制焊丝在平、立、横、仰焊位置下电弧较稳定且脱渣较容易;熔敷金属抗拉强度为601 MPa,屈服强度为540 MPa,断后伸长率为25.0%,-60℃冲击吸收功为113~120 J,扩散氢含量为2.90~3.12 mL/100 g,-25℃CTOD值为0.375~0.451 mm.EH460立焊接头抗拉强度为591~593 MPa,焊缝和热影响区-40℃平均冲击吸收功分别为153 J和180 J.焊缝金属以针状铁素体为主,冲击断口主要呈韧窝形貌.钛碱型渣系配合Ti-B复合微合金化促进了焊缝中针状铁素体的形成,结合多层降氢工艺实现了低扩散氢与高低温韧性的良好匹配.
To meet the requirements of low diffusible hydrogen,high toughness,and all-position weldability for 55 kg-grade low-alloy high-strength steel structures used in offshore engineering,bridges,and low-temperature service,a 1.2 mm-diameter gas-shielded flux-cored wire was developed using a titania-basic slag system and a Mn-Si-Ni-Ti-B-RE multicompo-nent alloying system.The diffusible hydrogen content was controlled through steel-strip cleaning,flux powder classification baking,and in-line wire redrying.The welding operability,deposited-metal chemical composition and mechanical proper-ties,diffusible hydrogen content,crack tip opening displacement(CTOD),and microstructure were systematically evaluated,and the joint performance was verified using EH460 steel plates.The results show that the developed wire exhibits a stable arc,low spatter,and easy slag removal in the flat,vertical,horizontal,and overhead positions.The deposited metal achieves a tensile strength of 601 MPa,a yield strength of 540 MPa,an elongation after fracture of 25.0%,and an impact absorbed en-ergy of 113-120 J at-60℃.The diffusible hydrogen content is 2.90-3.12 mL/100 g,and the CTOD value at-25℃ranges from 0.375 to 0.451 mm.The vertically welded EH460 joints exhibit tensile strengths of 591-593 MPa,with all fractures oc-curring in the heat-affected zone.The average impact absorbed energies of the weld metal and heat-affected zone at-40℃are 153 J and 180 J,respectively.The weld metal is predominantly composed of acicular ferrite(volume fraction approxi-mately 90%-95%),and the impact fracture surfaces are characterized mainly by dimple morphology.The combination of the titania-basic slag system with Ti-B composite microalloying promotes acicular ferrite formation in the weld metal,and the multi-stage hydrogen-reduction process achieves a favorable balance between low diffusible hydrogen and high low-temperature toughness.
信国松;刘晓茹;邹勇;常朝祥;方乃文;牛董山钰
聚力新材料科技(日照)有限公司,山东 日照 276826聚力新材料科技(日照)有限公司,山东 日照 276826山东大学,山东 济南 250000中焊科技发展(哈尔滨)有限公司,黑龙江 哈尔滨 150028中焊科技发展(哈尔滨)有限公司,黑龙江 哈尔滨 150028中焊科技发展(哈尔滨)有限公司,黑龙江 哈尔滨 150028
矿业与冶金
55kg级低温高韧性药芯焊丝钛碱型渣系针状铁素体
55 kg-gradelow-temperature toughnessflux-cored wiretitania-basic slag systemacicular ferrite
《电焊机》 2026 (8)
116-122,7
国家自然科学基金(52261044)泰山产业领军人才工程(2024001)
评论