High joint efficiency achieved in ultra-light Mg-Li alloy by electron beam welding with controlled heat inputOA
For ultra-light Mg-Li alloys with a high Li content,fusion welding is a challenge due to the relatively active main alloying elements Mg and Li.In this study,electron beam welding technology was applied for the first time to join 8-mm-thick forged Mg-12Li-3Al-2Zn-1Si-1Y alloy plates.By controlling the heat input,defects in the welded joints and elemental evaporation were minimized.However,for the Mg-12Li-3Al-2Zn-1Si-1Y alloy,the Mg_(2)Si eutectic phase segregates at the fusion-zone grain boundaries during rapid solidification of the molten pool,thereby promoting the precipitation of coarse Mg_(3)(Al,Zn)phases along the boundaries.This segregation weakened intergranular atomic bonding in the fusion zone,leading to reduced deformability.Consequently,tensile fracture of the welded joints occurred in the fusion zone.With increasing heat input,the precipitation ofα-Mg phases around Mg_(3)(Al,Zn)phases at the grain boundaries improved the deformability of the grain boundaries.As the fusion zone and heat-affected zone were strengthened,fracture shifted to the base material,which became the weakest region.Under these conditions(with the heat input ranging from 123.4 to 164.6 J/mm),the joint efficiency exceeded 95%,and the ultimate tensile strength was approximately 280 MPa.When the heat input was further increased,grains in the heat affected zone coarsened,creating a softened zone where fracture occurred.This study provides a theoretical basis for electron beam welding of high-Li-content Mg-Li alloys,and offers a solution for their joining applications.
Peng Sun;Yangyang Xu;Qi Li;Yuyan Tang;Yang Jin;Jiaxin Yu;Lingfan Yi;Yuchuan Huang;Jiawei Sun;Lianmei Wu;Fei Li;Jiyi Dong;Changjiang Chen;Yonghua Shen;Linda Ke;Wencai Liu
National Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,ChinaNational Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,ChinaNational Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,ChinaBeijing Institute of Electronic System Engineering,52 Yongding Road,Beijing 100854,ChinaShanghai Aerospace Equipments Manufacturer Co.,Ltd,100 Huaning Road,Shanghai 200240,ChinaNational Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,ChinaNational Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,ChinaNational Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,ChinaNational Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,ChinaBeijing Institute of Electronic System Engineering,52 Yongding Road,Beijing 100854,ChinaBeijing Institute of Electronic System Engineering,52 Yongding Road,Beijing 100854,ChinaShanghai Aerospace Equipments Manufacturer Co.,Ltd,100 Huaning Road,Shanghai 200240,ChinaShanghai Aerospace Equipments Manufacturer Co.,Ltd,100 Huaning Road,Shanghai 200240,ChinaShanghai Spaceflight Precision Machinery Institute,76 Guide Road,Shanghai 201600,China Shanghai Engineering Technology Research Center of Near-Net-Shape Forming for Metallic Materials,76 Guide Road,Shanghai 201600,ChinaShanghai Spaceflight Precision Machinery Institute,76 Guide Road,Shanghai 201600,China Shanghai Engineering Technology Research Center of Near-Net-Shape Forming for Metallic Materials,76 Guide Road,Shanghai 201600,ChinaNational Engineering Research Center of Light Alloy Net Forming and State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai Jiao Tong University,800 Dongchuan Road,Shanghai 200240,China
矿业与冶金
Electron beam weldingHigh-Li-content Mg-Li alloyMicrostructure evolutionFracture and strengthening mechanisms
《Journal of Magnesium and Alloys》 2026 (4)
P.223-240,18
financially supported by the National Defense Basic Research Program(No.JCKY2023204A005)National Natural Science Foundation of China(52571148)Project of High Modulus Magnesium Alloy Forgings(JXXT-2023-014hbza)Research Program of Joint Research Center of Advanced Spaceflight Technologies(No.USCAST2023-3).
评论