Heat treatment effects on microstructure,deformation mechanisms and mechanical response in additive friction stir deposited Mg-Gd-Y-Zr alloyOA
Additive friction stir deposition(AFSD),as a solid-state-additive manufacturing technique with a high deposition rate,provides an innovative route for fabricating high-performance magnesium(Mg)alloys while avoiding solidification defects.In this study,the effects of T6 heat treatment on the microstructure,mechanical properties,and deformation mechanisms of an AFSD Mg-9Gd-3Y-0.5Zr(wt.%)alloy were systematically investigated.The AFSD alloy exhibited a heterogeneous onion-ring microstructure composed of alternating fine grains(~3.9μm)enriched with nanoscale cuboid Mg24(Gd,Y)5 precipitates and coarse grains(~10.6μm)containing limited precipitates,which originated from the non-uniform precipitate distribution in the feedstock.The T6 heat treatment eliminated dislocation structures,introduced abundant nano-Mg7(Gd,Y)(β'')precipitates and coarsened the fine and coarse grains to ~7.3 and ~67.4μm,respectively.Consequently,the AFSD and AFSD-T6 alloys achieved superior strength-ductility combinations compared to the feedstock,with yield strength/ultimate tensile strength/elongation of 293.5 MPa/330.3 MPa/8.1%and 366.8 MPa/374.3 MPa/5.1%,respectively.The heterogeneous grains induced pronounced hetero-deformation-induced hardening in both conditions,while basal<a>slip activity was progressively enhanced during deformation.However,extensive twinning,particularly double twinning in the coarse grains of the AFSD-T6 alloy,led to reduced ductility.Overall,this work demonstrates that coupling AFSD with tailored heat treatment enables effective microstructural heterogeneity engineering,offering a robust strategy for developing Mg-Gd-Y-Zr alloys with outstanding mechanical performance.
Hui Wang;Gang Zeng;Chengwei Zhou;Yidi Li;Biaobiao Yang;Ruilin Lai;Chenying Shi;Dikai Guan;Hao Wang;Yujie Cui;Yunping Li
State Key Laboratory of Powder Metallurgy,Central South University,Changsha 410083,ChinaHunan Provincial Technology Innovation Center of New Light Alloy Materials for Aerospace,CASIC(Changsha)Advanced Materials Institute Co.,Ltd,Changsha 410205,ChinaHunan Provincial Technology Innovation Center of New Light Alloy Materials for Aerospace,CASIC(Changsha)Advanced Materials Institute Co.,Ltd,Changsha 410205,ChinaState Key Laboratory of Powder Metallurgy,Central South University,Changsha 410083,ChinaIMDEA Materials Institute,C/Eric Kandel 2,Getafe 28906 Madrid,Spain Department of Materials Science,Polytechnic University of Madrid/Universidad Politécnica de Madrid,E.T.S.de Ingenieros de Caminos,28040 Madrid,SpainResearch Institute of Light Alloy,Central South University,Changsha 410083,ChinaCollege of Chemistry and Chemical Engineering,Central South University,Changsha 410083,ChinaDepartment of Mechanical Engineering,University of Southampton,Southampton SO171BJ,United KingdomCo-Creation Institute for Advanced Materials,Shimane University,1060 Nishi-Kawatsu-cho,Matsue,Shimane 690-8504,JapanBeijing Advanced Innovation Center for Materials Genome Engineering,University of Science and Technology Beijing,Beijing 100083,China Key Laboratory for Advanced Materials Processing(MOE),University of Science and Technology Beijing,Beijing 100083,China Beijing Laboratory of Metallic Materials and Processing for Modern Transportation,Institute for Advanced Materials and Technology,University of Science and Technology Beijing,Beijing 100083,ChinaState Key Laboratory of Powder Metallurgy,Central South University,Changsha 410083,China
矿业与冶金
Additive friction stir depositionMg-rare earth alloyHeat treatmentMicrostructureMechanical properties
《Journal of Magnesium and Alloys》 2026 (4)
P.313-337,25
financially supported by Science and Technology Major Project of Changsha(kh2401034)The Science and Technology Innovation Program of Hunan Province(2024JK2053)the Fundamental Research Funds for the Central Universities of Central South University(1053320240180)financial supports from the Science and Technology Innovation Program of Hunan Province(2022RC1081).
评论