首页|期刊导航|Journal of Magnesium and Alloys|Discussion of the influence of Al content on the microstructure and mechanical properties of Mg-xAl-Zn alloys fabricated by wire arc additive manufacturing

Discussion of the influence of Al content on the microstructure and mechanical properties of Mg-xAl-Zn alloys fabricated by wire arc additive manufacturingOA

中文摘要

Aluminum(Al)acts as the primary alloying element in Mg-Al-Zn alloys,so its content is of crucial importance for the samples fabricated by wire arc additive manufacturing(WAAM).However,microstructure and property fluctuations of the alloys induced by varying WAAM processes hinder the extracting of consistent Al content-microstructure-property relationships from existing studies.In this study,Mg-xAl-Zn(x=3,6,9,12)alloys were fabricated via WAAM using consistent process parameters to focus on the influence of Al content alone.The results indicate that all of the four alloys primarily consist ofα-Mg grains and Mg17Al12 phase.As Al content increases,theα-Mg grain size decreases from 43.1μm in Mg-3Al-Zn to 19.7μm in Mg-12Al-Zn.The content of Mg17Al12 phase increases from near 0%in Mg-3Al-Zn to 7.78%in Mg-12Al-Zn,and a sudden increase observed when Al content reached 12 wt%.The microhardness and yield strength of WAAM Mg-xAl-Zn alloys increase linearly with the increasing of Al content,which is attributed to the synergistic effects of grain refinement strengthening,solid solution strengthening,and second-phase strengthening induced by Al content.However,when the Al content reaches 9 wt%,the elongation and tensile strength decreased because of the excessive Mg17Al12 phase.Among the investigated alloys,Mg-6Al-Zn achieves the optimal strength-ductility balance,with a tensile strength of 266.3±0.4 MPa and an elongation of 13.9±1.4%.Thus,alloys with an Al content of approximately 6 wt%exhibit favorable performance and can be used without heat treatment,while those with Al content exceeding 9 wt%require heat treatment to optimize microstructure and improve ductility.

Yuxuan Tu;Dongdong Zheng;Zhuo Li;Ze Xu;Deqiang Chen;Chenghang Zhang;Huaming Wang

School of Materials Science and Engineering,Beihang University,37 Xueyuan Road,Beijing 100191,China Ningbo Institute of Technology,Beihang University,Ningbo 315800,China National Engineering Laboratory of Additive Manufacturing for Large Metallic Components,Beihang University,37 Xueyuan Road,Beijing 100191,ChinaNational Engineering Laboratory of Additive Manufacturing for Large Metallic Components,Beihang University,37 Xueyuan Road,Beijing 100191,China Research Institute of Aero-Engine,Beihang University,37 Xueyuan Road,Beijing 100191,ChinaSchool of Materials Science and Engineering,Beihang University,37 Xueyuan Road,Beijing 100191,China Ningbo Institute of Technology,Beihang University,Ningbo 315800,China National Engineering Laboratory of Additive Manufacturing for Large Metallic Components,Beihang University,37 Xueyuan Road,Beijing 100191,ChinaSchool of Materials Science and Engineering,Beihang University,37 Xueyuan Road,Beijing 100191,China National Engineering Laboratory of Additive Manufacturing for Large Metallic Components,Beihang University,37 Xueyuan Road,Beijing 100191,ChinaNingbo Institute of Technology,Beihang University,Ningbo 315800,ChinaNingbo Institute of Technology,Beihang University,Ningbo 315800,ChinaSchool of Materials Science and Engineering,Beihang University,37 Xueyuan Road,Beijing 100191,China National Engineering Laboratory of Additive Manufacturing for Large Metallic Components,Beihang University,37 Xueyuan Road,Beijing 100191,China

矿业与冶金

Mg-Al-Zn alloyAl contentWire arc additive manufacturingMechanical propertiesMicrostructure

《Journal of Magnesium and Alloys》 2026 (2)

P.480-496,17

supported by the National Key Research and Development Program of China(grant No.2023YFB4603302)the National Natural Science Foundation of China(grant No.52375162)the Ningbo Natural Science Foundation Young Doctoral Innovation Research Project(grant No.2024J433).

10.1016/j.jma.2026.101990

评论